Focusrite saffire pro 24 driver windows 10 + видео обзор

Focusrite saffire pro 24 driver windows 10

Если существует то, что вы прежде всего должны искать в вашем первом аудиоинтерфейсе, то это качественные преампы. К сожалению, многим пришлось усвоить печальный урок, купив аудиоинтерфейс с плохими преампами. Многие аудиоинтерфейсы хорошо делают свою работу, но когда дело доходит до преампов, те дают грубый и ненасыщенный звук, а сам интерфейс начинает периодически перезагружаться. Сложно представить, чтобы кто-то из вас хотел иметь в своем распоряжении такой аудиоинтерфейс.

Преампы, по существу, это, извините за каламбур, усилители, которые готовят звук для усилителя. Они получают сигнал с микрофона, и этот сигнал испытывает чрезвычайный недостаток в полноте. Преамп способствует усилению этого сигнала, и в идеале это происходит без видоизменения качества звука.

Но, как ни крути, дешевые преампы влияют на качество звука. Насыщая звук, многие дешевые преампы оживляют только высокие частоты, делая звук, в результате, хрупким и шероховатым.

Рекомендовать Saffire Pro 24 можно уже только из-за его качественных преампов. Просто-напросто, не существует другого аудиоинтерфейса в этом диапазоне цен, способного предложить преампы такого же качества. Есть, конечно, Mbox Mini, который тоже совсем неплох и находится в этом же ценовом диапазоне. Но в этом случае преимуществом Saffie Pro 24 становятся его 4 входа и делают его несомненным выбором из этих двух моделей.

Несмотря на то, что Saffie Pro 24 афишировался как аудиоинтерфейс имеющий 16 входов и 8 выходов, эта цифра не полностью соответствует действительности и получается из-за функции Saffire закольцовки выходов на входы. Давайте просто взглянем на физические входы Saffie Pro 24:

• 2 комбинированных входа XLR Mic/Line на передней панели (это означает, что вы можете подключить микрофонный джек или разъем 1/4 ‘’ в эти входы)
• 2 комбинированный инструментальных входа XLR (только для 1/4 ‘’)
• 6 линейных выходов 1/4 ‘’ на задней панели
• Линейный выход 1/4 ‘’ для подключения наушников на передней панели

Устройство идет также с некоторыми на удивление высококачественными плагинами эффектов, такими как компрессия, реверберация и эквалайзер. Естественно, это особенно хорошо работает в паре с потоком аудио, поступающим от конкретно данного аудиоинтерфейса.

Пожалуй, единственным слабым местом, которое вы сможете найти у этого аудиоинтерфейса, окажется его латентность, которая колеблется в 8 мс. Как бы там ни было, она достаточно низкая, поэтому не представляет из себя серьезной проблемы.

Даже с упомянутой выше незначительной жалобой, Focusrite Saffire Pro 24 превосходит всех своих конкурентов. Он имеет лучшие преампы в своем ценовом диапазоне, он надежен и имеет больше входов и выходов, чем его ближайший соперник в вопросах качества, MBox Mini. Если вы хотите приобрести аудиоинтерфейс, можете больше ничего не искать и не пробовать, Focusrite Saffire Pro 24 – лучший выбор!

• Платформа: Mac или персональный компьютер
• Высота (мм): 45
• Ширина (мм): 220
• Вес (кг): 1,6
• Глубина (мм): 215

Соединения фронтальной и задней панелей:

• Аналоговые канальные входы (входы 1 – 4): 2 комбинированных входа XLR mic/line Neutric, 2 комбинированных инструментальных входа XLR Neutric (инструменты только на входы 1 и 2)
• Цифровые канальные входы: (входы 5 – 14) 44,1 – 96 кГц, стерео S/PDIF вход на RCA, 1 x 8-миканальный вход ADAT на оптическом разъеме, 6 x аналоговые выходы TRS (выходы 1 – 6), 1 x TRS стерео выход на наушники

Плюсы: теплые преампы; четыре входа; комплект плагинов.

Минусы: латентность могла бы быть лучше.

Заключение muztorg.ru:
Прекрасные микрофонные преампы делают этот аудиоинтерфейс лучшим вложением ваших денег.

Нашел в описании ошибку? Выдели неточный текст и нажми Ctrl+Enter.

Курьерская доставка

Доставка по регионам с розничными магазинами Музторг

Доставка на следующий день

При заказе от 5 000р. доставка транспортной компанией для Вас будет либо бесплатной, либо со скидкой до 10% от суммы заказа.

Бесплатная доставка (или скидка до 10%) не распространяется:

Время доставки – осуществляется в течение дня.

Условия получения заказа на следующий день

Доставка на последующие даты

Точные сроки и стоимость доставки будут рассчитаны при оформлении заказа. Вы сможете выбрать подходящий вариант.

Бесплатная доставка до двери.
Бесплатный подъем грузов до 30 кг.
При весе товара более 30 кг – стоимость подъема согласно тарифам грузоперевозчика.

Доставка и оплата по России и СНГ

Преимущества доставки

Условия бесплатной доставки заказов от 5000 руб.

При заказе от 5 000 руб. доставка транспортной компанией будет либо бесплатной, либо со скидкой до 10% от суммы заказа.

Условия не распространяются:

Бесплатная доставка не подразумевает подъем на этаж цифрового пианино и заказов общим весом более 30 кг.

Почему выбирают «Музторг»

Гарантия качества

Возврат и обмен

Мы всегда идем навстречу нашим Покупателям и решаем спорные вопросы в Вашу пользу.

Выдержки из него:

С полным текстом Гарантийного обязательства Вы можете ознакомиться здесь.

Источник

Focusrite saffire pro 24 driver windows 10

It seems my Focusrite Saffire Pro 26 will not «play nice» with my new Win 10 PC.

I think I need the 1394 Legacy driver.

I downloaded a 1394 Legacy installer (It’s a KB installer) but it doesn’t appear to actually install the legacy driver anywhere I can find it.

How (Where?) can I get the Legacy 1394 driver, and get my computer to see it, so it can be usefully installed? Is it even possible?

Anyone have a clue?

Thank you, in advance!

What’s been happening is that the Saffire Unit will connect and lock on, and work perfectly but then suddenly disconnect itself.

Also, another strange thing is that when I connect a USB midi cable (from a keyboard) to one of the computer’s USB ports I get a loud hum (like a ground loop hum) which I’ve never experienced before.

Maybe I need to just do a clean install of Win 7?

When I had to use the legacy driver in Windows 7 for firewire, all I had to do was select it. Seems MS removed it as of Windows 8. Sigh.

Ok I found this info on a forum that seems promising:

Also check what they say here:

Maybe it needs to be downloaded then switched to:

I don’t have a win10 machine handy to install it on that has FW other than my main DAW but the latest FW stack works so it doesn’t really matter to me. Also, that article is pretty old, the one time I needed the legacy driver was back in windows 8 and haven’t needed it since so be sure this is the problem that actually needs solving.

I remember that particular article (it’s why I needed the legacy driver temporarily until RME fixed the driver issue), it was resolved by RME near the end of the thread FWIW removing the need for the legacy driver but that was for RME.

Strange you should say this.

After doing a few (I thought) unrelated tweaks, having to do with computer performance settings, power options, etc. the Saffire has been solid. Don’t know why. Will have to watch over a few days so. here’s hoping.

Still haven’t figured the ground loop hum, yet.

tried making sure the computer and the keyboard are plugged into different wall sockets. Nope.

Strange you should say this.

After doing a few (I thought) unrelated tweaks, having to do with computer performance settings, power options, etc. the Saffire has been solid. Don’t know why. Will have to watch over a few days so. here’s hoping.

It’s definitely much more stable.

Almost perfect, but still, every now and then, I see the «firewire locked light» flicker on and off.

Lost sound once or twice so there’s still more road to travel.

Saffire firewire range (Pro 14, Pro 24, Pro 24 DSP, Pro 26, Pro 40, Liquid Saffire 56)

Works with Windows 10 Fall Creators Update? YES

If you are unsure about the compatibility of your firewire chipset, please download this tool, and run OHCItool.exe. If it reads «This controller is not compatible with DICE drivers» or «Compatibility Unknown», then you’ll need to replace your firewire card with a compatible one.

Also make sure there aren’t any apps competing for the SC using different sample rates, that would likely cause the lock light to flicker during the transition. You might also consider setting the outputs in Reaper to higher than 1/2, such as 3/4 then routing that in MixControl to physical 1/2 (I would assume that’s possible). The reason is the OS will default to 1/2 and this keeps them separate.

Interesting, I’ve been experiencing an identical problem with my Saffire Pro 40.
The light flickers and the it cause the audio to skip.
I have used OHCI tool and it the chipset is one that is approved by Focusrite.

On my system it only happens when my CPU is under a medium to heavy load.
I’ll try routing REAPER to a different output and see if that helps.
It’s interesting to hear I’m not the only one having this problem, for a while I thought my saffire was dying, but it seems to be a windows 10 issue.

This is the one suggestion that kind of popped out at me when I read it.

One, I’ve discovered that the unit is powered just fine without plugging in it’s «wall wart». Interesting. Any pro’s or con’s to allowing the computer to power the unit?

Second, I changed the firewire cable itself and I haven’t had a audio/software drop, yet. I think it may have been the firewire cable itself, all along. Will watch and report.

Another piece of info about the «hum» is that it only sound off when both an audio AND a USB cable are plugged in, at the same time. It so happens, that both are plugged into the same keyboard.

Maybe it needs to be downloaded then switched to:

I don’t have a win10 machine handy to install it on that has FW other than my main DAW but the latest FW stack works so it doesn’t really matter to me. Also, that article is pretty old, the one time I needed the legacy driver was back in windows 8 and haven’t needed it since so be sure this is the problem that actually needs solving.

I remember that particular article (it’s why I needed the legacy driver temporarily until RME fixed the driver issue), it was resolved by RME near the end of the thread FWIW removing the need for the legacy driver but that was for RME.

May I suggest a trial
If you have the latest version of Reaper installed uninstall it
And install version 5.75.
I have had many problems with the new version of Reaper installed.
Reaper is behaving for me much better with this installed.
Will not hurt to try this quick and easy.

Everywhere I could think of, in C drive, but couldn’t find it. I even found places on the net that indicated the path of installation but never found it there.

So far, so good. Doesn’t appear, at the moment that I’ll need it.

1.Right-click the Legacy1394.inf file under one of the following paths based on the computer’s architecture:

C:\Program Files\1394 OHCI Compliant Host Controller (Legacy)\x86_driver

C:\Program Files\1394 OHCI Compliant Host Controller (Legacy)\x64_driver

Yeah, that looks like the same article I was referencing. I went to that address and found the folders (86, 64) but no driver in it.

Yeah, that looks like the same article I was referencing. I went to that address and found the folders (86, 64) but no driver in it.

Yeah, sorry, that’s what I meant (knew it was something like that). It’s not there.

Yes, I installed the 64 version.

FYI that I just found that the article has at typo, the x64 package gets installed in Program Files (x86), then in the x64 Driver folder you should see the inf file:

Focusrite saffire pro 24 driver windows 10

Someone made a boo boo when creating the installer. Focusrite saffire pro 24 driver windows 10

Wait, are you telling me, that’s it.

I tried to access it through Device Manager to update the driver, and while it would let me get to the folder, the folder itself would not open to reveal it’s content. I figured the reason it wouldn’t do so was because there was no driver contained therein.

Is that (.inf file) the legacy driver?

It’s the description file that helps get it installed, the actual driver is ohci1394.sys. So do the same drill via device manager and manually browse to that folder instead or do it how the article describes by just browsing to the folder via computer and installing, then going to device manager to switch from modern to legacy.

After you install the 1394 OHCI Legacy Driver.msi file, follow these steps:

1.Right-click the Legacy1394.inf file.
2.Click Install.
3.Open Device Manager in Control Panel.
4.Expand IEEE 1394 Bus host controllers, and then locate the host controller.
5.Right-click the host controller, and then click Update Driver Software.
6.Click Browse my computer for driver software.
7.Click Let me pick from a list of device drivers on my computer.
8.Click Generic1394 OHCI compliant host controller (Legacy), and then click the Next button.
9.Click the Close button.

This is the step I did not know or understand.

However, right now everything has been running rock solid for hours so I am cool.

Good to know though.

Would a «hum isolator» help with the USB and audio cable debacle? The hum wasn’t present on my Win 7 machine.

Very often yes, they are expensive but I keep a few around for such reasons (hums wherever they occur). Which kind are you considering? There are several types, one that plugs into AC and ones that go inline with signal cables and I’m not sure which one will solve your issue.

The guesstimate is the one that goes into the AC socket is what you need but it is a ground «loop» so placing it on the outputs of your sound card may also work (or not), it’s down to testing stuff etc. to be sure. It is nice to have a couple lying around though, because they simply make testing and life easier. Focusrite saffire pro 24 driver windows 10

Exactly what is the signal chain? What devices are in that chain. Are the connections balanced or unbalanced? What cables are used?

These are the details that matter when determining the cause and best solution to ground loop noise.

Just following up with my findings as I have a similar problem.

I feel pretty certain that for me this is an issue with a recent update to Windows 10
It definitely doesn’t have anything to do with REAPER, it can happen whatever I’m doing as long as their is a medium to heavy load on the CPU.
My firewire chipset is one of the ones that Focusrite still recommends

I have 2 Focusrite pro 40’s
They both have the light flickering audio cutting out problem with windows 10.
I have used this computer with the exact same hardware for years running windows 8 windows 10 and as a Hackintosh, I had no issues until a couple months ago after an update to windows 10.

Both these interface still work completely fine with my Mac Book
It doesn’t seem to have anything to do with the power or firewire cable used. (the same cables work fine for my mac and always worked fine until recently with windows)

I’m not sure if this helps, but I had to go back to Legacy firewire drivers to use my firewire interface in Windows 7.

Also, I had intermittent dropouts with my system and was going crazy tracking it down until I finally figured out that the Windows 7 CDRom driver was screwing things up. I disabled my CDRom and everything has been great since.

There are some latency checker system utilities available. I’m not sure if they run under Win10 but they helped me troubleshoot. My system has been gold for several years since I tracked down the problems.

Just following up with my findings as I have a similar problem.

I feel pretty certain that for me this is an issue with a recent update to Windows 10
It definitely doesn’t have anything to do with REAPER, it can happen whatever I’m doing as long as their is a medium to heavy load on the CPU.
My firewire chipset is one of the ones that Focusrite still recommends

I have 2 Focusrite pro 40’s
They both have the light flickering audio cutting out problem with windows 10.
I have used this computer with the exact same hardware for years running windows 8 windows 10 and as a Hackintosh, I had no issues until a couple months ago after an update to windows 10.

Both these interface still work completely fine with my Mac Book
It doesn’t seem to have anything to do with the power or firewire cable used. (the same cables work fine for my mac and always worked fine until recently with windows)

Источник

Focusrite Saffire Pro 24 Mac Driver

Focusrite saffire pro 24 driver windows 10

Focusrite Saffire Pro 24 Mac Driver and Software Downloads. This installer includes all necessary drivers and software to run the firewire Saffire range of Focusrite interfaces.

Focusrite Saffire Pro 24 Mac Driver Downloads

Operating Systems: Mac OS X 10.6, Mac OS X 10.7, Mac OS X 10.8, Mac OS X 10.9, Mac OS X 10.10, Mac OS X 10.11, Mac OS X 10.12, macOS 10.13, macOS 10.14
File Name: saffire-mixcontrol-1.84_0.dmg, Size: 18.2MB
System requirements: Apple Macintosh with a high-speed USB 2.0-compliant USB port.
Note: (Unsupported Legacy Version). This version of Saffire Mix Control is the most recent version to retain compatibility with OS X 10.4.11 (Tiger). Please note: this version of Saffire MixControl is no longer supported.

Focusrite saffire pro 24 driver windows 10

– Focusrite Saffire Pro 24 Mix Control v1.8 Mac Download
– Focusrite Saffire Pro 24 Mix control 1.8 Release Notes Download

Saffire Pro 24 Mix Control 3.7: Includes a fix for Saffire interfaces that would not retain their Sync Source in standalone mode.Includes a fix for OS X users seeing the “No Hardware Connected” message and experiencing disconnects on account of there being 2 drivers installed (after the 3.5/3.6 upgrade).
Includes a fix to keep Saffire Mix Control running after new firmware is deployed to the Saffire interface.

– Focusrite Saffire Pro 24 Mix Control v3.7 Mac Download

RTAS MixControl 1.0: RTAS MixControl is a utility plug-in that enables Pro Tools users to blend monitor mixes between audio inputs and DAW outputsignals during tracking, enabling performers to benefit from true zero-latency monitoring.
– RTAS MixControl 1.0 Mac Download
– RTASSMC-User_Guide.pdf Download

User Guides: Saffire Pro 24 – ENG – FR – DE – ESP – JP.
FireWire safety when plugging and unplugging devices: This article explains the steps necessary to safely plug in and unplug your FireWire devices without causing damage to the device or your computer- Download.

Focusrite Saffire Pro 24 Mac Driver downloads includes the latest Mac drivers — we update daily.

Источник

Видео

Focusrite - Saffire Pro 14 and Saffire Liquid 56 on Windows 10 - Versión 21H2 (Semi-Stable)

Focusrite - Saffire Pro 14 and Saffire Liquid 56 on Windows 10 - Versión 21H2 (Semi-Stable)

Что такое звуковая карта обо всем по немногу focusrite saffire pro 24 dsp

Что такое звуковая карта обо всем по немногу focusrite saffire pro 24 dsp

Focusrite Saffire "Нет подключения к оборудованию"

Focusrite Saffire "Нет подключения к оборудованию"

Подключение Focusrite Saffire PRO 14

Подключение Focusrite Saffire PRO 14

Interface Setup Guide (Focusrite Saffire 6 USB)

Interface Setup Guide (Focusrite Saffire 6 USB)

Аудио интерфейс FOCUSRITE SAFFIRE PRO 24 io Firewire

Аудио интерфейс FOCUSRITE SAFFIRE PRO 24 io Firewire

Saffire Pro 40 - Windows 10 - July/August updates Audio Bug

Saffire Pro 40 - Windows 10 - July/August updates Audio Bug

Focusrite Saffire PRO 14 FireWire Demonstration on a Custom PC Build | macOS Big Sur | Hackintosh

Focusrite Saffire PRO 14 FireWire Demonstration on a Custom PC Build | macOS Big Sur | Hackintosh

Обзор Saffire Pro 24 с тестом задержки

Обзор Saffire Pro 24 с тестом задержки

Focusrite Saffire PRO 14, Rode NT1-A

Focusrite Saffire PRO 14, Rode NT1-A
Поделиться или сохранить к себе:
Добавить комментарий

Нажимая на кнопку "Отправить комментарий", я даю согласие на обработку персональных данных, принимаю Политику конфиденциальности и условия Пользовательского соглашения.